Hunter-fan 42711-01 Manual do Utilizador

1Form# 42711-0120091118©2009 Hunter Fan Co.Set & $aveSet & $aveSet & $aveinstallation andoperation manualModel44260ProgrammableThermostatE

10G RC RH Y Wif your existing thermostat is marked...label the wire with this sticker:G / FGGW / H / BW/BW/BY / C* / M / OY/0Y/0RC / VCRCRCRH / R / VR

114. Using the provided stickers, label each wire according to the chart. (If the terminals are not labeled, contact a qualied HVAC

12WRCYG

13INSTALLING THE THERMOSTATINSTALLING THE WALL PLATE1. Remove the wall plate from the new thermostat by pressing the release tab on the bottom of the

14WRCYG

154. Remove the wall plate and drill two 3/16” holes where marked. 5. Tap the plastic anchors into the holes until they are ush with the wall. 6. Rep

16GRCRHY/0W/BRCGY1Y/0W/BY1Terminal Shield

17INSTALLING THE THERMOSTAT, CONT.CONNECTING THE WIRES1. Loosen, but do not remove, the terminal screws. Note: A jumper wire has been provided, connec

18DISABLEENABLERECOVERYHGHEGSYSTEM TYPESTDHPW/B Y/O RH RCY1FAN OPTIONAMHEAT4TThermostat CoverSystem SwitchGRC RH Y/O W/B Y1

19ATTACHING THE THERMOSTATLift the thermostat cover and set the SYSTEM switch to OFF and the FAN switch to AUTO. 1. Locate the HE/HG switch on the ba

2

2012Tab

214. Place the top of the thermostat over the two tabs on the wall plate. Press the thermostat onto the wall plate and press to snap the bottom tab in

22reset

23The default setting of the thermostat is Fahrenheit (Fo). NOTICE: CHANGING THIS SETTING WILL RESET THE THERMOSTAT TO FACTORY DEFAULT PROGRAMS. (If

24day/timeAMPM

25The default for this thermostat setting is in a 12 hour format. You can change the format to 24 hour format by pressing Day/Time and then Program. T

26AMHEAT4T

27This thermostat gives you the ability to program up to 4 custom temperature settings per day or utilize pre-programmed settings. For manual operatio

28AMHEAT2TH

291. MANUAL OPERATIONMany people prefer to operate their thermostats manually, adjusting settings as needed. You can either temporarily override the s

3Table of ContentsImportant Information ... 5Tools 6 Uninstalling the Existing Unit ...

30hold/returnsystemoffheatcoolHOLD

31MANUAL OPERATION, CONT.If you want to permanently override all settings and adjust the thermostat manually:1. Press Hold/Return until the Hold icon

3210 pm8 am6 amProgram 1Heat : 68o F (20o C)Cool : 78o F (26o C)Program 2Heat : 60o F (16o C)Cool : 85o F (29o C)Program 3Heat : 68o F (20o C)Cool : 7

33METHODS OF OPERATION, CONT.2. DEFAULT PROGRAMSBy using the pre-programmed settings, this thermostat can save you money by optimizing energy usage in

34AMPMprogramhold/returnsystemoffheatcool

35METHODS OF OPERATION, CONT.3. CREATING CUSTOM PROGRAMS• Program times can be set in 10 minute increments.• Program temperature can be set in incre

36AMPMHEAT COOLSA21 3 4SUM T W TH Fprogramhold/returnsystemoffheatcool

373. Press Up or Down to change the hour. Press Program to save the hour and adjust the minute setting. 4. Press Up or Down to change the minute. Pres

38FILTERfilter

39ICONS AND FEATURES1. INDIGLO® Night-Light - will backlight the display for easy viewing in the dark. Press any button to illuminate the light. (I

4Congratulations!Thank you for choosing a Hunter programmable thermostat. Your new Hunter thermostat will provide years of reliable service and year-r

40HEAT COOLsystemoffheatcoolreset

413. Span setting mode – allows you to adjust the system ON/OFF cycle rate. The default setting is 2 (the system cycles ON or OFF when the temperature

42STAGE 1PMCOOL4MSTAGE 2

434. Low battery warning – indicates two stages of battery power shortage. When the batteries are detected as weak, the icon will ash until new AA

44hold/return

455. Auto recovery – allows heating and cooling systems to gradually recover from an energy-saving setpoint temperature to a comfort setpoint temperat

46

476. Error mode – indicates an unexpected battery problem. The screen will ash an ERR message and shut your system off until the batteries are replac

481. Temperature Range2. Compressor ProtectionAfter the system stops running in cooling mode, there will be a 3.5 minute delay before it can be restar

49WIRING

5This thermostat is designed to work on the following heating and cooling systems:Gas – Standing PilotGas – Electronic IgnitionGas – Fired BoilersGas

50WIRING, CONT.

51WIRING, CONT.

521. My display will not come on. 1 a. Check batteries and battery connections. 1 b. Reset the thermostat. ...

535. My heating or cooling will not turn on or off. 5 a. Check the Heat/Cool function switch to ensure it is set to the desired position. 5 b. Wait. T

547. My system continues to operate when the thermostat is in the off position. 7 a. Replace unit. ...

55Is there help on the web? Yes. Visit http://www.hunterfan.com for more information. ...

6This thermostat includes two #8 slotted screws and two wall anchors for mounting.To install your new thermostat, you will need the following supplies

7NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ens

8YRCGWYRCGW

91. Turn the system power OFF from the existing thermostat. Turn the power to the HVAC system OFF at the main power panel or at the furnace. 2. Remove