Hunter-fan 40170 Manual do Utilizador

Electronic/MechanicalermostatModel 40170installation andoperation manual42998-01 01-19-2007

10UNINSTALLING THE EXISTING UNIT, CONT.if your existing thermostat is marked...label the wire with this sticker:G / FGGW / HWWY / C* / MYYRC / VCRCRCR

114. Using the provided stickers, label each wire according to the chart. (If the terminals are not labeled, contact a qualified HVAC

12Top CoverThermostat

13INSTALLING THE THERMOSTATINSTALLING THE THERMOSTAT1. Remove the top cover from the new thermostat by pulling the two halves apart.

14WRCYG

152. Position the new thermostat on the wall and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunt

16INSTALLING THE THERMOSTAT, CONT.GRCRHYWB ORHRCWGBOY

17INSTALLING THE THERMOSTAT, CONT.CONNECTING THE WIRES1. Loosen, but do not remove, the terminal screws. Note: A jumper wire has been provided, conne

18INSTALLING THE THERMOSTAT, CONT.HGHEHPSTDHE/HG SwitchHP/STD Switch

19ATTACHING THE THERMOSTAT1. Locate the HE/HG switch on the wall plate. Set the switch to HG for a gas furnace or oil burner. Set the switch to HE fo

2

20INSTALLING THE THERMOSTAT, CONT.

213. Insert two fresh AA alkaline batteries. 4. Align the top cover with the the wall plate, and snap the two halves together. 5. Restore power at

22AUTOONCOOLOFFHEATSYSTEM9007060580Fan SwitchSystem SwitchSet Temperature Slider

23OPERATION1. Set the Set Temperature slider to the desired temperature. 2. The System Switch determines the operating mode of the thermostat. Selec

24INDICATORS AND ADUSTMENT0506078090ThermometerBattery Indicator

25INDICATORS AND ADUSTMENT1. The Thermometer indicates the room temperature.2. The Battery Indicator displays two battery conditions. The first warnin

26SPANSpan AdjustSPAN

27INDICATORS AND ADJUSTMENTS, CONT.1. Remove the top cover from the thermostat. 2. To make your system run LONGER, turn the Span Adjust clockwise.3.

281. My heating or cooling will not turn on or off. 1 a. Check the HE/HG switch to ensure it is set to the correct position. 1 b. Wait. There may be a

29Is there help on the web? Yes. Visit http://www.hunterfan.com for more information. ...

3Table of ContentsImportant Information... 5Tools ...

30GRcRhWYFan RelayHeat/Cool24V SupplyCoolContactorHeat Relayor ValveXJumper4-wire Heat/Cool SystemGRcRhFan RelayHeat24V SupplyWHeat Relayor ValveYCool

31WIRING DIAGRAMSReversingValveCompressorContactorXFanRelayHeat/Cool24V SupplySingle-stage Heat Pump SystemCoolModeHeatModeORWGRcRhOBYXJumperRcRhWHeat

32GRcRhWHeat 24V SupplyHeat Relayor ValveXJumper3-wire Heat Only SystemFan RelayGRcRhWHeat 24V SupplyHeat Relayor ValveXJumper3-wire Heat Only SystemF

33© 2007 Hunter Fan Company

4Congratulations!Thank you for choosing a Hunter thermostat. Your new Hunter thermostat will provide years of reliable service and year-round energy s

5This thermostat is designed to work on the followingheating and cooling systems:Gas – Standing PilotGas – Electronic IgnitionGas – Fired BoilersGas –

6This thermostat includes two #8 slotted screws and two wall anchors for mounting.To install your new thermostat, you will need the following supplies

7NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ens

8UNINSTALLING THE EXISTING UNITYRCGWYRCGW

91. Turn the system power OFF from the existing thermostat. Turn the power to the HVAC system OFF at the main power panel or at the furnace. 2. Remo